Specifies calculation types of points

Specifies initial value for a global or derived point.

is string containing the initial value for the point.

is boolean indicating if the point is local. Local points can be used to hold intermediate values of expressions. The value of local points are not available to applications, they are only used internally by the derived point process to perform calculations.

is string containing the expression for the point.

is string containing the interval to update the timer counter point. The format is HH:MM:SS using a 24 hour clock.

is string containing the start time for the timer counter point. The format is HH:MM:SS using a 24 hour clock

is a string specifying the derived point process supporting this point. Normally this will be 'SPM' or '_PTDP_RP'. This must identify a valid derived point processor process ID. It should not be changed unless you are using structure point processing

is a string containing the name of the reset point.

is a long integer defining the roll over value for delta accumulator function.

is long integer defining the maximum variance value to be used for delta accumulator functions.

is a string indicating the device specific address of the point

is an integer indicating the address offset of the point. Typically used for addressing a boolean point in an analog domain

MMS types

is an variant containing the analog deadband for the point. The point will not be updated until a change that exceeds the deadband is read.

is boolean indicating the point should only be loaded into memory if it's requested by an application. Defaults to False.

is a string indicating the device the point is on

is a boolean used to enable or disable Just-In-Time. Note this is only available when this is a class Data Item comming from the Class configuration

is boolean indicating if the point should be polled immediately after a setpoint. If False, the point is not polled until the next scheduled scan cycle

is an integer indicating the scan rate of the point in multiples of the base scan rate of the communications port.

defines the trigger condition for a device point. See the Point Configuration documentation for additional information

is variant containing the trigger value. Trigger value is used when specifying a CimDevicePoint.TriggerType relation that requires a value

defines update criterias available for device points. The particular types of update that are actually available depend on the device communication module being used

is a string containing the equation used to convert the value from device units to engineering units. To use a custom expression you must first disable the linear conversion for the object. If the point is not read-only a reverse expression must be specified to allow a setpoint in engineering units to be translated back to device units. It is your responsibility to make sure these expressions yield the correct results

is a string containing the EuLabel. Note you cannot specify an EuLabel if using a measurement unit for the point

is a string containing the equation used to convert the value from engineering units to device units. To use a custom expression you must first disable the linear conversion for the object. A forward expression must also be specified. It is your responsibility to make sure these expressions yield the correct results

is a variant containing the high converted value used for linear conversion with a string representation of 10 characters or less. Larger values will be rejected. To use linear conversion you must set linear conversion to True

is a variant containing the upper raw value used for linear conversion with a string representation of 10 characters or less. Larger values will be rejected. To use linear conversion you must set linear conversion to True

is a boolean indicating if the conversion is linear or custom

is a variant containing the low converted value used for linear conversion with a string representation of 10 characters or less. Larger values will be rejected. To use linear conversion you must set linear conversion to True.

is a variant containing the low raw value used for linear conversion with a string representation of 10 characters or less. Larger values will be rejected. To use linear conversion you must set linear conversion to True.

The Text property gets and sets the text of the point enum field.

The numeric value of the point enum field.

The SetpointAllowed property gets and sets if a setpoint is allowed with this enum text for the point.

is number that hlds the first (or left hand) side of the opperand if the value is to be treated as a number. Use CimClassDataItemExpression.FirstOperandString if your value is a string

is string that hlds the first (or left) hand side of the opperand. Use CimClassDataItemExpression.FirstOperandNum if your value is a number

is a read only attribute that represents the ID of this expression

Specifies the browser type

is number that hlds the first (or left) hand side of the opperand if the value is to be treated as a number. Use CimClassDataItemExpression.SecondOperandString if your value is a string

is string that hlds the second (or right hand) side of the opperand. Use CimClassDataItemExpression.SecondOperandNum if your value is a number

The string identifier of the measurement unit.

Contains informative information about the measurement unit.

Contains the full name of the measurement unit such as ”hour” or ”meter per second”.

The display label of the measurement unit is typically the abbreviation of the measurement unit, for example ”h” for hour or ”m/s” for meter per second.

Identifies the organization (company, standards organization) that defines the measurement unit.

Numeric identifier for programmatic evaluation. -1 is used if a unitId is not available.

object provides an interface to CIMPLICITY Alarm configuration

is a boolean indicating if alarming is configured for the point

defines types of alarming available

is a boolean indicating if the alarm generation should be delayed. When alarm delay is enabled specify the TimeInterval and TimeUnit for the delay. AlarmDelay cannot be used with a Rate of Change alarm criteria

contains a variant indicating the alarm high limit for the point

contains a variant indicating the alarm low limit for the point

is a string containing the point alarm message to be used when an alarm is generated for the point

is a boolean indicating if the moving alarm to normal state should be delayed. When alarm off delay is enabled specify the TimeInterval and TimeUnit for the delay. AlarmOffDelay cannot be used with a Rate of Change alarm criteria

is a integer containing the Alarm String to use when generating point alarms. Defaults to 1

is a boolean indicating if the %VAL field in the alarm message should be updated while the point is in ana alarm state

is a string containing the name of the deviation point. The deviation point must be specified when the alarm criteria is cimAlarmDeviation

is a variant containing a numeric value indicating the delay interval when alarm goes into the Warning High state

defines units for time values

is a variant containing a numeric value indicating the delay interval when alarm goes into the Alarm High state

defines units for time values

is a variant containing a numeric value indicating the delay interval when alarm goes from the Alarm High state to Normal state

defines units for time values

is a variant containing a numeric value indicating the delay interval when alarm goes from the Warning High state to Normal state

defines units for time values

is a variant containing a numeric value indicating the delay interval when alarm goes into the Warning Low state

defines units for time values

is a variant containing a numeric value indicating the delay interval when alarm goes into the Alarm Low state

defines units for time values

is a variant containing a numeric value indicating the delay interval when alarm goes from the Alarm Low state to Normal State

defines units for time values

is a variant containing a numeric value indicating the delay interval when alarm goes from the Warning Low state to Normal state

defines units for time values

is a variant containing a numeric value indicating the time interval when using a rate of change or alarm delay

defines units for time values

contains a variant indicating the warning high limit for the point

contains a variant indicating the warning low limit for the point

is a long integer containing maximum age in seconds of a sample to keep

is a long integer containing the maximum number of samples to keep